Web Analytics
Part Datasheet Search > Semiconductors & Actives > PCA9552 Datasheet PDF
Images are for reference

PCA9552 Datasheet PDF

Part Series:
PCA9552 Series
Category:
Semiconductors & Actives
Description:
LED DRVR 16Segment 2.5V/3.3V/5V 24Pin TSSOP
Updated Time: 2023/01/13 02:37:09 (UTC + 8)

PCA9552 Datasheet PDF Semiconductors & Actives

158 Pages
NXP
LED Driver 2.5V/3.3V/5V 24Pin TSSOP Bulk
158 Pages
NXP
LED Driver 2.5V/3.3V/5V 24Pin SO T/R
158 Pages
NXP
LED DRVR 16Segment 2.5V/3.3V/5V 24Pin SO
158 Pages
NXP
LED DRVR 16Segment 2.5V/3.3V/5V 24Pin HVQFN EP
158 Pages
NXP
16Bit I2C-bus LED driver with programmable blink rates
27 Pages
NXP
Driver; PWM dimming; LED controller; I2C; 25mA; Channels:16

PCA9552PW Specifications

TYPE
DESCRIPTION
Mounting Style
Surface Mount
Number of Pins
24 Pin
Supply Voltage (DC)
5.50V (max)
Case/Package
TSSOP
Number of Outputs
16 Output
show more

PCA9552PW Function Overview

Overview
The PCA9552 LED blinker blinks LEDs in I²C-bus and SMBus applications where it is necessary to limit bus traffic or free up the I²C-bus master"s (MCU, MPU, DSP, chip set, etc.) timer. The uniqueness of this device is the internal oscillator with two programmable blink rates. To blink LEDs using normal I/O expanders like the PCF8574 or PCA9554, the bus master must send repeated commands to turn the LED on and off. This greatly increases the amount of traffic on the I²C-bus and uses up one of the master"s timers. The PCA9552 LED blinker instead requires only the initial setup command to program BLINK RATE 1 and BLINK RATE 2 (that is, the frequency and duty cycle) for each individual output. From then on, only one command from the bus master is required to turn each individual open-drain output on, off, or to cycle at BLINK RATE 1 or BLINK RATE 2. Maximum output sink current is 25 mA per bit and 200 mA per package.
Any bits not used for controlling the LEDs can be used for General Purpose Parallel Input/Output (GPIO) expansion.
The active LOW hardware reset pin (RESET) and Power-On Reset (POR) initializes the registers to their default state, all zeroes, causing the bits to be set HIGH (LED off).
Three hardware address pins on the PCA9552 allow eight devices to operate on the same bus.
MoreLess
## Features
16 LED drivers (on, off, flashing at a programmable rate)
2 selectable, fully programmable blink rates (frequency and duty cycle) between 0.172 Hz and 44 Hz (5.82 seconds and 0.023 seconds)
Input/outputs not used as LED drivers can be used as regular GPIOs
Internal oscillator requires no external components
I²C-bus interface logic compatible with SMBus
Internal power-on reset
Noise filter on SCL/SDA inputs
Active LOW reset input
16 open-drain outputs directly drive LEDs to 25 mA
Edge rate control on outputs
No glitch on power-up
Supports hot insertion
Low standby current
Operating power supply voltage range of 2.3 V to 5.5 V
0 Hz to 400 kHz clock frequency
ESD protection exceeds 2000 V HBM per JESD22-A114, 150 V MM per JESD22-A115 and 1000 V CDM per JESD22-C101
Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA
Packages offered: SO24, TSSOP24, HVQFN24
## Features
show more
Part Datasheet PDF Search
Loading...
72,405,303 Parts Datasheet PDF, Update more than 5,000 PDF files ervery day.

Relate Parts